| Description of hull and super structure standards: |
- Solid fiberglass hull
- UV resistant, high gloss ISO gelcoat
- Built in spray rails and speed rails
- Hydrodynamic, tapered stern post
- Molded fiberglass shoe ( integrated with hull )
- Two piece molded superstructure from foredeck to back of wheelhouse and molded in non-skid finish
- Molded fibreglass helm station
- Fiberglass roof with visor, laminated to wheelhouse
- PVC grab rails on wheelhouse and cuddy roof
- Bow cleat, stern and bow staples
- Cored deck, wheelhouse and roof
- Sliding door on Teflon tracks
- Drain plug in keel
- Heavy duty PVC gunwale molding
- Radar arch
- 10 PVC fixed windows
|
| Deck Hatches |
- Deck hatches are aluminum set in Stainless Steel frames, common size 24” x 24”, any size available.
- Bomar Hatch in cuddy 24 x 24
- 5’ x 4’ Aluminum water tight hatch over engine
|
| Shafting |
Straight shaft assembly complete with:
- 13' X 316 SS shaft comes with brass nut
- Stainless Steel shaft log with cutlass bearings and inside box
- 4 bolt heavy duty steady bearing
- Shaft coupling
- Anodes
- Installation
- Dripless shaft system 2 ¼”
- Hy torque propeller Blade
|
| Steering |
| Single station powering steering complete with:
- Hydraulic pump comes with pulley, 6 gal tank Stainless Steel, 1 gal reservoir, belt and mounting bracket
- Steering unit comes with 15" Stainless Steel steering wheel, Stainless Steel spindle and mounting plate
- Dual ram steering unit with nitrated steel piston shafts
- Hydraulic hoses, fittings
- 2" Stainless Steel rudder stock and 28" X 26"X 1/4" Stainless Steel rudder with support wings
- Installation
|
| Fuel Tanks |
- 2 Stainless Steel fuel tanks constructed with 11 gauge 2B finish plate
- 2" fill lines and 2" Stainless Steel deck fills
- 1" vent lines
- 3/4" suction hose (hydraulic hose) from one tank
- shut off valve
- inter connecting line (3/4" hydraulic hose )
- 3/8" return line to one tank
- installation
- 2 tank whistlers
- 300 gal
|
| Wash-down / Bailing Pump |
- Jabsco 1” 3-way ball valve
- bronze fittings
- 1” thru hull and seacock
- reinforced PVC hoses
- fire hose comes with Lexon nozzle and polypropylene quick disconnect fittings
- Installation
|
| Electrical |
- Custom 20-circuit breaker panel comes with 100 Amp main breaker and ammeter
- Group 8D cranking battery
- Battery box #4 electrical mains, #2/0 starter cables
- 4 running lights - port, starboard, stern, masthead
- Stainless Steel dome lights
- 7 search light Jabsco 200,000 Candle power
- 2 Pantograph windshield wipers - heavy duty
- Rule 3700 GPH bilge pump, 3-way switch, float, hose
- Deck lights
- 4 gang way switch
- 3-way bilge switch
- Engine room lights
- Installation
|
| Engine Installation |
- Installation alignment and bolting
- Solid fibreglass engine beds
- Kobelt controls and cables twin
- 6” wet exhaust through stern / no muffler
|
| Accommodations |
- Table with benches
- Top and bottom
- Cupboard and counter top
- Manual marine toilet with brass fittings, thru hulls, including enclosure
- 4 outlet engine heater
- Builders Risk
|
| Options |
- Stainless Steel Bow rail
- Sliding windows PVC Starboard side
- Lettering
|
